Test and Measurements

EXFO Power Meter Trouble Shooting

PPM-350C Troubleshooting The PPM-350C PON Power Meter was designed for two main purposes: Suit FTTP testing needs and to be easy to use for people who are not necessarily familiar with fiber optics in FTTx. Be used as a standard optical power meter (OPM operation mode). Solving Common Problems Problem Possible Cause Solution One of […]

FTTH Network

JDSU Light Source Maintenance

Before you start to maintenance Light Source, read the following words thoroughly: Maintenance or cleaning of the device when it is connected up or operating may damage the device or injure you. Make sure that the device is switched off and disconnected from all power sources and optical radiation sources before maintenance or cleaning. The […]

Test and Measurements

CWDM OTDR JDSU MTS-6000A and -8000 Platforms

CWDM OTDR Module Introduction This JDSU CWDM OTDR module, support to work with JDSU MTS-6000A and JDSU MTS-800 platform. This CWDM OTDR EVO family able to characterize CWDM fiber network by connecting to any location of the fiber networking, during CWDM network commissioning, network upgrades, and troubleshooting. The optical performance of the CWDM module, combined […]

Test and Measurements

EXFO Power Meter Calibration

Power Meter Calibration Introduction When it comes to calibration, it is not enough to state that an instrument complies with published specifications; it is necessary to be ready to prove it and to have a state-of-the-art system in place to monitor and preserve the quality of all calibrations. In 1998, EXFO decided to adopt the […]

HOW-TO

How to do FSM-11S Splicer Arc Calibration

Step by Step guide for FSM-11S Arc Calibration Atmospheric conditions such as temperature, humidity, and pressure are constantly changing, which creates variability in the arc calibration. This splicer is equipped with temperature and pressure sensors that are used in a constant feedback control system to regulate the arc power at a constant level. Changes in […]

Fiber Splicing

Maintenance of FSM-11S SpliceMate Splicing Quality

Maintenance of Splicing Quality 1. Cleaning and Checking before Splicing Critical cleaning points and maintenance checks are described below . 1-1. Arc Power Calibration Refer to [Arc Calibration] (Page 42). 1-2. Cleaning V -grooves If contaminants are present in the V -grooves, proper clamping may not occur, resulting in higher splice loss. The V -grooves […]

FEATURES Optical Cable

Advantages Of Fiber Optics

Optical Fiber Advantage in telecommunication 1. Immunity to Electromagnetic Interference Although fiber optics can solve data communications problems, they are not needed everywhere. Most computer data goes over ordinary wires. Most data is sent over short distances at low speed. In ordinary environments, it is not practical to use fiber optics to transmit data between […]

FEATURES FTTH Network

Componentes FTTx

OLT, ONT, ODN, Fiber, Divido FTTH network consisting OLT, ONT / ONU, ODN, the ODN network fiber composite, dividers, etc. Fiber Installation of fiber optic cable is one of the most expensive items in the PON deployment and how to proceed depends on several factors, including cost, rights of way, legal standards, aesthetics, etc., and […]

FTTH Network

Tecnologías utilizadas en FTTx

FTTx Technology New standards such as those established by ITU-T, the IEC and the Institute of Electrical and Electronics Engineering (IEEE), have greatly increased standardization of design, survivability and safety of PONs. It offers the opportunity to economies scale and lower costs, no conceivable above. Tables 1 and 2 describe the main parameters that define […]

FTTH Network

FTTx Introducción

Introducción a FTTx La fibra óptica monomodo, con su ancho de banda prácticamente ilimitado, es ahora el medio de transporte preferido en redes de transporte largo y metropolitanas. La utilización de cable de fibra óptica (en lugar de cable de cobre) reduce significativamente los costes del equipo y de mantenimiento, a la vez que aumenta […]